Acura integra 1995 gsr rebuild?

kevinkevin
in Cars & Transportation

hi i am ready to do a rebuild on my 95 integra gsr, ive look on ebay for a rebuild kit, i know all of you dont recommend ebay, but well give it a try.

my motor is not blown or anything still runnning like a champ, 250k miles very high.

i change oil every week, to keep it healthy until i do a rebuild.

i dont no my bearings and piston ring size, i dont want to order the wrong thing.

a mechanic told me just get standard size if its not blown motor , but another mechanic told me get it measured. i dont want to pay extra for em to checc it out.

the reason for this rebuild is to feel the usual gsr power.

please help.

http://www.ebay.com/itm/Acura-Integra-GSR-1-8L-B18...

http://www.ebay.com/itm/160815374689?ssPageName=ST...

these r the rebuild kit what do you suggest

should i just get standard size.

Update:

so should just buy a regular kit without bearings n pistons, so when i do rebuild it he could check it out then. you are right, i dont want waste more money, gettin the wrong kit.

but whats the chances of the walls having marks, high percentage. or do i have a better chance going forward and get the standard size, need your answerrr

btw thanks for the link

Comments

  • curiousadultcuriousadult

    sorry but the links you provide me are not a full rebuild kit

    this is the rebuild kit you want

    http://www.ebay.com/itm/94-95-HONDA-ACURA-INTEGRA-...

    comes with what you need to rebuild on the engine block only

    the head does not have a rebuild kit and requires individual parts if needed

    now usually i dont order until i disassembled and inspect the whole engine then order

    because lets say i found lots of marks on the piston walls so i need to bore and hone it bigger

    so the kit i already order has standard size and now i have to reorder new pistons and rings which cost more money but sometimes honing might just do it so you can keep standard size

    remember if you dont want any problems make sure you check for flatness or resurface the head and the block

    get it hot tanked

    HEAD: inspect the valves make sure its not bent and get it cleaned up and do a valve job on the head and grind the valves to get it to seat properly

    always replace the valve stems no matter what

    check your lost motion assembly if it sticks its bad

    thats about it just make sure you follow your manual and you should be good to go

    EDIT!!!!

    what you should do is wait til you fully disassemble your engine and inspect everything then start deciding what to do and what to order

    the chances of having wall marks cannot be determine until it is inspected

  • joe-murray_60b84fef26ee1joe-murray_60b84fef26ee1

    1995 Acura Integra Gsr

  • anonymousanonymous

    This Site Might Help You.

    RE:

    Acura integra 1995 gsr rebuild?

    hi i am ready to do a rebuild on my 95 integra gsr, ive look on ebay for a rebuild kit, i know all of you dont recommend ebay, but well give it a try.

    my motor is not blown or anything still runnning like a champ, 250k miles very high.

    i change oil every week, to keep it healthy until i do a...

  • adam-hunter_60b84ff09d365adam-hunter_60b84ff09d365

    1

  • isabelle-clark_60b84ff18e845isabelle-clark_60b84ff18e845

    Battery is dead, which has likely caused your alternator to die as well.. Get someone to give you a jumpstart if that works, then get a new battery and get your alternator tested, you will likely have to get a new alternator too, but you want to check it first. Good luck.

  • atlloveatllove

    you will have better luck and smarter answers if you check on a acura/ honda forum. lots of those guys can be d*cks but they know what they are talking about.

  • pete-jpete-j

    the cylinders and bearings will all wear different. run it until a problem develops and do it right.

Sign In or Register to comment.

© Vanilla Keystone Theme 2024